User
Reference Gemini-1
Oscillator 1 and 2
|
Waveform type |
Sine, saw, ramp, triange
or pulse wave, white and pink noise |
|
Sync (Osc2) |
Synchronizes osc 2 to osc 1 |
|
Pitch |
Sets the pitch for the oscillator. Range: +/- 1
octave |
|
Fine |
Fine tuning of the pitch. Range: + /- 1 semitone |
|
Width |
Width of the pulse waveform (when selected) |
|
PWM |
Pulse Width Modulation depth controlled by lfo 1(osc1) or lfo2 (osc2) |
|
MOD |
Pitch modulation depth controlled by the modulation
wheel |
|
LFO 1/2 |
Pitch modulation depth controlled by lfo1 |
Filter 1 and 2
|
Type |
High pass (HP) Low pass (LP) Bandpass
(BP) and Band Reject (REJ) |
|
Freq |
Frequency of the filter |
|
Res |
Resonance level of the frequency |
|
Vel |
Keyboard Velocity depth to the Filter |
|
LFO 1/2 |
Frequency modulation depth controlled by lfo 1 / 2 |
|
MOD |
Frequency modulation depth controlled by the
modulation wheel |
|
ADSR |
Attack, Decay, Sustain and Release settings for the
filter envelope |
VCA 1 and 2
|
Level |
Level of the VCA |
|
LFO 1/2 |
Level modulation depth controlled by lfo 1 / 2 |
|
Pan |
Panorama setting of the VCA Left / Right |
|
Vel |
Keyboard / Step Velocity depth to VCA |
|
Step |
Routes the output of the step sequencer to VCO 1 / 2 |
LFO 1
|
Type |
Waveform of the LFO, Sine, saw, ramp, triange or pulse wave |
|
Rate |
Speed of the LFO |
|
Delay |
Delay (fade in) of the LFO at key trigger |
|
Release |
Release time of the LFO after key release |
LFO 2
|
Type |
Waveform of the LFO, Sine, saw, ramp, triange or pulse wave |
|
Rate |
Speed of the LFO |
|
Sync |
Synchronizes the speed of LFO 2 to LFO 1 |
EG 1 / 2
|
ADSR |
Attack, Decay, Sustain and Release settings for the
level envelope |
Bend
|
|
Bend range for the pitch bend controller ( 0 – 12
semitones) |
Porta
|
|
Portamento time
(legato only) |
MOD
|
Rate |
Modulation speed for the modulation wheel |
Ring
|
On / Off |
Ring modulator on /off switch |
|
Pitch |
Sets the pitch of the modulation signal |
Delay
|
Level |
Send (input) level for the delay |
|
Mono / dual |
Mono or Dual delay times (Left / Right) In mono mode
Left rotary sets delay time for left and right) |
|
Left |
Left delay time |
|
Right |
Right delay time |
|
Feedback |
Sets the amount of feedback |
Flanger
|
On / Off |
Flanger on / off
switch |
|
Rate |
Speed of the flanger
effect |
|
Depth |
Depth of the flanger
effect |
Step sequencer
|
Steps +/- |
Sets the number of steps 1-8 |
|
Divide |
Divides the incoming tempo pulse (host) changing the
step rate |
|
Run** |
Starts / stops the step sequencer |
|
Key |
When active the sequencer acts as an Arpeggiator. It starts running when a key is pressed and
stops when it is released. The sequencer resets at key release. |
|
Reset |
Resets the sequencer to step 1 |
|
2ND row |
Determines the function of the 2nd row of knobs. Pitch osc 2 / Filter vcf 1 + 2 |
|
Pitch knobs 1-8 |
Sets the pitch for each of the 8 steps |
|
Level faders |
Sets the level for each of the 8 steps |
|
Pitch knobs (2ND row) |
Sets the pitch or filter frequency for each of the 8
steps (depending on the position of the 2ND row selector) |
MIDI
|
Channel |
|
|
Step |
Routes the output of the stepsequencer
(1st row only + velocity) to the midi output. *When step selector
is set to OFF then the |
**NOTE: Known issue
Sometimes the sequencer stops running spontaneously. It appears to be
related to the release setting
Of the ADSR’s. When you
experience this problem try experimenting with the release setting. I am
currently working on a solution…