User Reference Damatriks

Fixed audio path:

 

VCO1, 2, 3, NOISE -> Audiomix -> VCA 1 -> filter 1 -> filter 2 -> phaser -> delay => Output

 

 

 

 

Midi/cv

Midi input LED

Indicates incoming Midi note data

Velocity

Sets the amount of velocity depth to the vca

P Bend

Sets the pitchbend range: +/- 2 octaves

Mod lfo1

Sets the depth of pitch modulation applied by the mod wheel from lfo1

 

VCO 1 and 2

Course

Pitch course: +/- 1 octave

Fine

Fine tuning: +/- 1 semitone

CV

CV depth

Width

Pulse width (only when pulse waveform is selected)

Range

Pitch range: 16,8,4

Wave

Waveform select: > Saw, ^ Triangle,  ¬ pulse

PWM

Pulse width modulation

 

VCO Link

<sync<

Synchronizes the waveform of VCO 1 to VCO 2

<Xmod<

Crossmodulation of VCO 1 by VCO 2

 

VCA 3

Course

Pitch course: +/- 1 octave

Fine

Fine tuning: +/- 1 semitone

CV

CV depth

Range

Pitch range: 16,8,4

Wave

Waveform select: > Saw, ^ Triangle,  ~Sine

 

Audiomix

Inputs

Vco1, vco 2, vco 3, noise generator

 

Env 1/2

ADSR

Attack, Decay, Sustain, Release. Output= +/- 10Volt

Gate / Clock

Trigger select. Gate=Midi/cv input, Clock= Clock output

Neg

Switches output voltage to negative (-10Volt)

 

VCA 1

Gain

Input gain (from audiomix)

CV

CV depth

Env

Selects Envelope source: Env1, env2, Hold

 

Filter 1/2

Freq

Sets the Frequency

CV

CV depth of the frequency

selector

Low pass / Band pass (filt1), High pass / Band Pass (filt2)

Res

Resonance

 

Delay

Time L

Delay time

Time R

Delay time right (only in Stereo mode)

Feedback

Delay decay time

Stereo

Stereo / Mono mode switch

Mix

Mix dry / wet signal

 

Phaser

Rate

Speed of the phase cycle

depth

Phase range

Mix

Mix dry / wet

 

Clock         

Display

Speed in BPM

Freq

Speed of the Clock: 10-240 BPM

Source

Internal clock / Host Clock (Clock signal from VST Host software / DAW)

Reset

Reset clock / Step one of Stepsequencer

Run

Start / stop of the clock

 

Multiply

 

Multiplication of the clock BPM rate

˝

Half time

1

Exact BPM rate

1.33

Quarter Triplet

2

Double rate (8th notes)

3

Triplet

4

16th notes

 

Stepsequencer A

1-8 Knobs

Voltage of the steps

Range

1V (+/- ˝Volt), 2V (+/-1Volt), 10V (+/-5Volt)

Steps

Number of Steps (1-8)

 

The sequencer is triggerd by the Clock module

 

LFO 1/2

Rate

Speed of the lfo: 0-1Hz / 0-10Hz

Range (lfo1)

Switch between small or large range

CV

CV depth of the LFO speed

Shape (lfo1)

~Sine, > Saw, ¬ Pulse

Shape (lfo2)

~Sine, < Ramp, ¬ Pulse, Random

 

Output +/- 5Volt

 

S/H

Rate

Speed of the lfo: 0-1Hz / 0-10Hz

Hold

Hold source: Internal (as set by the rate knob) / Clock

Voltage

Voltage select of the Sample source: Random / CV input

 

Output 0-10Volt

 

CV Mix

1

CV input 1

2

CV input 2

 

Used to mix two CV sources together

 

CV Matrix

Inputs (vertical row)

All available CV modulation Sources

Outputs (horizontal row)

All available CV destinations

 

Every source can be routed to multiple destinations. Every destination can only have one source routed to it.

Wheel

Modulation wheel (from midi keyboard)

 

Out

Meter

Output level meter

Level

Output gain